International Journal of Innovative Research in Science, Engineering and Technology

International Journal of Innovative Research in Science, Engineering and Technology

Menu

ISSN ONLINE(2319-8753)PRINT(2347-6710)

All submissions of the EM system will be redirected to Online Manuscript Submission System. Authors are requested to submit articles directly to Online Manuscript Submission System of respective journal.

Microstructure, Mechanical properties and Dry sliding Wear behaviour of Al-Si-Mg alloy reinforced with Graphite

Amith.D.Gangadhar1, M.H.Annaiah2, T.G. Rajiv4, Manjunatha B4, Harendra kumar H.V5
 P G student, Department of Mechanical Engineering, Acharya Institute of Technology,Bangalore, Karnataka, India1
Professor and P G Coordinator, Department of Mechanical Engineering, Acharya Institute of Technology Bangalore, Karnataka, India2
Assistant Professor, Department of Mechanical Engineering, Acharya Institute of Technology, Bangalore, Karnataka, India3 Assistant Professor, Department of Mechanical Engineering, Acharya Institute of Technology, Bangalore, Karnataka, India4
P G student, Department of Mechanical Engineering, Acharya Institute of Technology, Bangalore, Karnataka, India5
Related article at Pubmed, Scholar Google

Visit for more related articles at International Journal of Innovative Research in Science, Engineering and Technology

International Journal of Innovative Research in Science, Engineering and Technology

Abstract

In this study, A356.0 alloys were reinforced with varied percentage of Graphite by liquid metallurgy route and tested for microstructure, mechanical properties. Wear tests were conducted using Pin-on-Disc apparatus at a constant sliding velocity of 1m/s and load of 30N. Microstructure revealed uniform distribution of reinforcement in the matrix resulting in improved mechanical properties and wear resistance compared to un-reinforced material. The ceramic reinforced alloys were found to have improvement in mechanical properties and wear resistance which may be attributed to the improved bonding of reinforcement in the matrix.

Keywords
Composites, MMC’s, Microstructure, Mechanical behaviour

INTRODUCTION
Aluminium-Silicon alloys possess light weight, high specific strength and good heat transfer ability which make them suitable material to replace components made of ferrous alloys. Al-Si alloys are widely used in all types of IC engines such as cylinder blocks, cylinder heads and Pistons. They find applications in aircraft pump parts, aircraft structure and control parts, automotive transmission, aircraft fittings, water cooled cylinder blocks and nuclear energy installations. Both hypoeutectic and hyper-eutectic alloys can be used as useful engine block materials on account of their adequate resistance and high strength to weight ratio. There are quite large numbers of studies made on the mechanical behaviour of Al-Si alloys. Attempts are made to increase the strength of Al-Si-Mg by various manufacturing processes, heat treatment, reinforcement of hard and soft reinforcements etc.
In this paper, an attempt is made to study the effect of varied percentage of reinforcement of Graphite on microstructure, mechanical properties and dry sliding wear behavior of A356.0

II. MATERIALS
A356.0 alloys were reinforced with Graphite and were cast using liquid metallurgy route in the form of cylindrical bars of length 300mm and diameter 25mm. Table I shows the chemical composition of A356.0 alloy and Table II shows the designation of the alloy and its composites.

III. TESTING
A: Microstructure
The samples for microstructure examination were prepared by following standard metallurgical procedures, etched in etchant prepared using 90 ml water, 4ml of HF, 4ml H2So4 and 2g CrO3 and were examined using Optical Microscope.
Figures 2.1 to 2.4 show the uniform distribution of ceramic reinforcement Graphite in A356.0 matrix.
B. Hardness test
The hardness tests were conducted as per ASTM E10 norms using Brinell hardness tester. Tests were performed at randomly selected points on the surface by maintaining sufficient spacing between indentations and distance from the edge of the specimen.
Table III Shows the hardness values of As cast A356.0 alloy and its composites. The hardness of 3G (3% Graphite) is found to be 59(BHN) compared to as cast alloy with hardness 51 indicating 15.69% increase in hardness. 5G (5% Graphite) has large value of 60. 10G has hardness of 53.
C: Tension test
Table IV shows plot of UTS and % elongation values of as cast A356.0 and its composites. It is clear from the table that UTS and Ductility increases with Graphite reinforcement for all composites such as G3, G5 and G10 compared to as cast values G3 has highest UTS and ductility compared to as cast and other composites. UTS of G3 are 149.07MPa which is 90.9% higher than UTS of as cast.G10 has 126.56MPa showing 61.43% increase in strength. The Elongation of G3 is 3.24% which is 149.2% higher than as cast A356.0.Composites G10 and G5 also have improved Ductility which are 118.46% and 93.8% respectively higher than as cast.
Fig 3.2 shows the plot of wear rate versus sliding distance of A356.0 and its composites. A356.0 has wear rate of 1.95x10-5 gm/m where as G3 has 1.45x10-5 showing 25.64% reduction in wear rate. This reduction in wear rate may be attributed to the increase in hardness achieved due to uniform distribution and bonding of the ceramic in the composite. Composites G5 and G10 have wear rate 1.1x10-5gm/m and 1.82 x10-5gm/m respectively. The decreased wear rate of G5 may be attributed to higher percentage of Graphite in the composite which act as solid lubricant results in reducing wear rate.

IV. CONCLUSION
Microstructure indicates uniform distribution of ceramics in the matrix resulting in good bonding of the particulates. The composite with 5% Graphite has highest hardness. Composite with 3% Graphite has highest UTS and ductility. Graphite reinforced aluminium alloys are proved to be better wear resistant materials compared to unreinforced alloys.

ACKNOWLEDGEMENT
We thank Dr. H. D. Maheshappa, Principal and Management of Acharya institute of Technology, Bangalore, India for motivating and providing research facilities at the institute.

Tables at a glance
Table icon Table icon Table icon Table icon Table icon
Table 1 Table 2 Table 3 Table 4 Table 5
 

Figures at a glance
Figure Figure Figure Figure
Figure 1 Figure 2 Figure 3 Figure 4


Figure Figure
Figure 5 Figure 6
 

References
  1. Saka, N., Pamies-Teixeira, J. J. and Suh, N. P. “Wear of two-phase metals”. Wear, 1977, 44, 77-86.
  2. S.C.Sharma, A.Ramesh, “Effect of heat treatment on Mechanical properties of particulate reinforced Al6061 composites”, Journal of Materials Engineering and Performance, vol.9(3) (2000) pp.344-349.
  3. S.C. Sharma, B.M. Girish, R. Kamath, & B.M. Satish, “Fractogrphy, Fluidity, and Tensile Properties of aluminum/Hematite Particle composite”, Jour. of Mat. Engg. & Perf., vol.8(3), 1999, pp.309-314.
  4. Venkataraman, B. and Sundararajan, G., “The sliding wear behavior of Al-Sic particulate composites-I.” Acta. Metall., 1996, 44, 451-460.
  5. Zhang, Z. F., Zhang, L. C. and Mai, Y.-W., “Scratch studies of Al-Li alloy reinforced with SIC particles.”Proc. 4th Int. Tribology Confi (Austrib 94), 5-8 Dec.1994, Perth, Australia, pp. 249-254.
  6. Wang, A. G. and Rack, H. J., “Abrasive wear of silicon carbide particulate and whisker-reinforced 7091 aluminum matrix composites”. Wear, 1991,146, 337-348.
  7. Feest, E. A., “Exploitation of the metal matrix composites concept”. Met.Mater., 1988, 4, 273-278.
  8. Zhang, Z. F., Zhang, L. C. and Mai, Y.-W., “Scratch studies of Al-Li alloy reinforced with SIC particles.” Proc. 4th Int. Tribology Confi (Austrib 94), 5-8 Dec.1994, Perth, Australia, pp. 249-254.
  9. Rohatgi, P., “Cast aluminum-matrix composites for automotive applications”. J. Met., 1991, 43, 10-15.
  10. Jahanmir, S. and Suh, N. P., “Mechanics of subsurface void nucleation in delamination wear”. Wear, 1977, 44, 17-38.